Rohde & Schwarz NRPC-LS – RF-Power Linearity Standard (Catalog 1421.7004.02)
$25,327.00
In Stock
In Stock
Commercial Pricing
Request for Quotations for Bulk Orders
Rohde & Schwarz NRPC-LS - RF-Power Linearity Standard (Catalog 1421.7004.02) Specs
| Signal frequency | 1 GHz |
| Measurand | RF linearity relative power measurement (ratio of two consecutive power measurements) |
| Test port power range | 1 GHz |
| range 1, internal RF attenuator on | -30 dBm to +27 dBm |
| range 2, internal RF attenuator of | -60 dBm to -3 dBm |
| DC | -10 V to +10 V |
| Test port connector | N female |
| Output impedance | 50 Ω |
| Insertion loss | between RF input and RF output |
| 0 dB to 21 dB level difference | 0.005 dB |
| level difference A | 0.0002 × A + 0.004 dB |
| 0 dB to 5 dB | 0.005 dB |
| > 5 dB to 10 dB | 0.006 dB |
| > 10 dB to 15 dB | 0.007 dB |
| > 15 dB to 20 dB | 0.008 dB |
| > 20 dB to 30 dB | 0.010 dB |
| > 30 dB to 40 dB | 0.012 dB |
| > 40 dB to 50 dB | 0.014 dB |
| > 50 dB to 57 dB | 0.016 dB |
| level difference A | 0.0002 × A + 0.006 dB |
| 0 dB to 5 dB | 0.007 dB |
| > 5 dB to 10 dB | 0.008 dB |
| > 10 dB to 15 dB | 0.009 dB |
| > 15 dB to 20 dB | 0.010 dB |
| > 20 dB to 30 dB | 0.012 dB |
| > 30 dB to 40 dB | 0.014 dB |
| > 40 dB to 50 dB | 0.016 dB |
| > 50 dB to 60 dB | 0.018 dB |
| > 60 dB to 70 dB | 0.020 dB |
| > 70 dB to 80 dB | 0.022 dB |
| > 80 dB to 87 dB | 0.024 dB |
| Resolution bandwidth (RBW) | single sideband (SSB) mode |
| recommended for linearity measurement | 1 kHz |
| Displayed average noise level (DANL) | test port power range 1, 1 GHz |
| test port power range 2, 1 GHz | < 103 dBm (1 Hz) |
| 1 GHz | –92 dBc (nom.) |
| test port power range 1, 1 GHz | -84 dBm (nom.) |
| test port power range 2, 1 GHz | -86 dBm (nom.) |
| Sensor type | R&S®NRQ6 frequency selective power sensor |
| Measurement function | recommended |
| Continuous average function | measurand |
| aperture | 8.3 ns to 30 s (depending on RBW) |
| duty cycle correction | 0.001% to 100.0% |
| capacity of measurement buffer | 1 reading to 8192 readings |
| Triggering | supported measurement functions |
| source | INTernal: internal test signal EXTernal[1]: host interface trigger signal (8-pin male M12 connector) EXTernal2: coaxial trigger I/O (SMA (f) jack) BUS: remote control event (*trg) |
| Averaging filter | parameters |
| supported measurement functions | continuous average, trace |
| averaging count | 1 to 65536 |
| moving mode | continuous result output, independent of averaging count |
| repeat mode | final result only |
| Internal reference frequency | accuracy |
| Intermediate frequency (IF) | RBW ≤ 40 MHz |
| mechanical | 8-pin male M12 connector (A-coded) |
| power supply | +5 V/0.1 A (USB low-power device; requires additional PoE+ power supply) |
| speed | high-speed and full-speed mode in line with USB specification |
| remote control protocols | USB test and measurement device class (USBTMC) |
| trigger input EXTernal[1] | differential (0 V/+3.3 V) |
| signal level | LVDS |
| input frequency | 20 MHz |
| permissible total cable length | ≤ 5 m |
| Ethernet interface (LAN PoE+) | mechanical |
| power supply | power over Ethernet (PoE+) class 4 |
| speed | 10/100/1000 Mbit/s |
| remote control protocols | VXI-11, high-speed LAN instrument protocol (HiSLIP), SCPI-RAW (port 5025) |
| permissible cable length | ≤ 100 m |
| Trigger 2 I/O (TRIG2) | mechanical |
| input | 10 kΩ or 50 Ω (software controlled) |
| output | 50 Ω |
| input | compatible with 3 V or 5 V logic, max. –1 V to +6 V |
| output | ≥ 2 V into 50 Ω load, max. 5.3 V |
| Reference clock I/O (REF) | mechanical |
| input/output | 50 Ω |
| input | ≥ –10 dBm |
| output | ≥ +7 dBm |
| input | 10 MHz |
| output | 10 MHz |
| Sample clock I/O (CLK) | mechanical |
| input/output | 50 Ω |
| output | ≥ -10 dBm |
| output | 119 MHz to 121 MHz |
| Local oscillator I/O (LO) | mechanical |
| input/output | 50 Ω |
| input | ≥ -5 dBm |
| output | ≥ 0 dBm |
| input/output | 70 MHz to 6.03 GHz |
| Temperature | operating temperature range |
| permissible temperature range | 0°C to +40°C |
| storage temperature range | -40°C to +70°C |
| Climatic resistance | damp heat |
| Mechanical resistance | vibration |
| sinusoidal | 5 Hz to 55 Hz, 0.15 mm amplitude, 1.8 g at 55 Hz, 55 Hz to 150 Hz, 0.5 g constant, in line with EN60068-2-6 |
| random | 8 Hz to 500 Hz, 1.2 g (RMS), in line with EN60068-2-64 |
| shock | 45 Hz to 2 kHz, max. 40 g shock spectrum, in line with MIL-STD-810E, method 516.4, procedure I |
| Air pressure | operating |
| transport | 566 hPa (4500 m) to 1060 hPa |
| Electromagnetic compatibility | complies with harmonized standards: EN61326-1, EN61326-2-1, EN55011 (class B) |
| Calibration interval | recommended |
| Dimensions | W × H × D |
| Weight | 4.2 kg (9.26 lb) |
Be the first to review “Rohde & Schwarz NRPC-LS – RF-Power Linearity Standard (Catalog 1421.7004.02)”
Reviews
There are no reviews yet.