TTi TGR2051 – 1.5GHz Synthesized RF Signal Generator
$2,247.00
In Stock
In Stock
Commercial Pricing
Request for Quotations for Bulk Orders
TTi TGR2051 - 1.5GHz Synthesized RF Signal Generator Specs
| Frequency Range: | TGR2053: |
| TGR2051: | 150kHz - 1500MHz |
| Setting Resolution | 10Hz |
| Setting Resolution Low Spur Mode: | 1MHz |
| Accuracy/Stability: | see Reference Frequency |
| Phase Noise: | 500MHz Carrier: <- 124 dBc/Hz (typ) @ 10KHz offset 1GHz Carrier: <- 117 dBc/Hz(typ) @ 10kHz offset See chart below |
| Residual FM: | <2 Hz @ 1GHz - Equivalent peak deviation in a 3000Hz to 3.4kHz bandwidth |
| Internal Reference Accuracy | <± 1ppm, 15ºC – 30ºC <± 2ppm, 5ºC – 40ºC |
| Internal Reference Stability | <1ppm/year |
| Reference IN & OUT | Both can be disabled when not required. |
| Reference IN | 10MHz +/- 25ppm, 50Ω input impedance, 2 - 5Vpp |
| Rear Panel BNC | Automatic detection and selection when an external reference signal is present and Ref. Clock is selected to be EXTERNAL. LCD status indicator shows when external reference is active. |
| Reference OUT | 10MHz, 50Ω output impedance, >2Vpp into 50Ω |
| Rear panel BNC | The active reference signal (from internal or external source) is present when Ref. Clock Out is selected to be ON. |
| Output Level Range | –127dBm to +13dBm |
| Setting Resolution | 0.1dB, 0.01uV –1mV |
| Accuracy | ±1dB output levels > -53dBm ±2dB output levels <= -53dBm |
| Additional Uncertainty AM, ASK & OOK ON | +/-0.5dB |
| Harmonically Related Signals | <-25dBc @ +13dBm, <-30dBc@levels <=0dBm |
| Non-harmonic Spurii | 10kHz offset 1.5GHz – 3GHz 10kHz offset 150KHz - 1.5GHz |
| Output Impedance | 50Ω |
| VSWR | <2.0 typ <=1.6 |
| RF Output Connector | Type N Female |
| Reverse Voltage Protection | 50V DC |
| Output Switch | RF OUT On/Off switch with LED showing ON status |
| Internal | DDS generator providing sine, square, + Ramp, - Ramp, triangle 1mHz – 1MHz, Resolution 1mHz |
| External | 100Hz – 1MHz, 1dB relative to 1kHz, 1Vp-p for full scale 10kΩ input impedance AC coupled |
| Deviation | 1mHz – 1MHz subject to carrier frequency |
| Deviation Setting Resolution | 1mHz |
| Deviation Accuracy | Ref freq accuracy +/- 1mHz for internal modulation ±2% for external modulation @ 1kHz, 1V p-p |
| Distortion | <1% @ 1kHz modulation, 300 – 3.4kHz bandwidth. |
| Deviation | 0 - 25.00 rad |
| Deviation Setting Resolution | 0.01 rad |
| Deviation Accuracy | Ref freq accuracy ±0.1rad for internal modulation ±2% for external modulation @ 1kHz, 1V p-p |
| Distortion | <1% @ 1kHz modulation, 300 – 3.4kHz bandwidth |
| Modulation Depth | 0 – 100% |
| Setting Resolution | 0.1% |
| Accuracy | ±1% for internal modulation ±2% for external modulation @ 1kHz, 1V p-p |
| Distortion | ≤1% @ ≤90% depth |
| Frequency settling time to within 100Hz or 0.1ppm of final frequency if greater | <5ms*, typ <2ms |
| Amplitude settling time to within 0.2dB | <5ms*, typ <4ms |
| Rear panel SYNC pulse width (defines guaranteed settling period) | 5ms * |
| Number of Points | 2 - 1000 |
| Formula specifies | Sweep Start and Stop Frequencies Sweep Start and Stop Amplitudes Dwell time following SYNC at each point |
| Dwell Time | 0.01 – 10.000sec |
| Sweep Mode | Continuous or Single |
| Sweep Direction | Up or Down |
| Sweep Point Spacing | Linear or Logarithmic |
| Sweep Trigger: (Sweep start held until trigger event) | Manual, ext signal +ve or –ve edge, timed (0.01 – 999.9sec) or via remote interface. |
| Point Trigger: (Sweep point stepping held until trigger event) | Manual, ext signal +ve or –ve edge, or via remote interface |
| Point Trigger timing | >=10ms after SYNC signal |
| SYNC signal (‘output stable’) | Available after output has settled at each point until the next point. Programmable high or low logic. |
| Trigger logic threshold: | +1.6V |
| USB | Standard USB 2.0 hardware connection. Operates as a virtual COM port. |
| LAN | Ethernet 100/10base-T hardware connection. |
| GPIB (optional) | Conforming with IEEE488.1 and IEEE488.2 |
| Frequency settling time to within 100Hz or 0.1ppm of final frequency if greater | <=15 ms typ <7ms |
| Amplitude settling time to within 0.2dB | <=15ms typ <4ms |
| Power | 85…264Vac, 47…63Hz, 35VA max. Installation Category II. Standby <0.5W |
| Display | 4.3 inch (10.9 cm) backlit TFT LCD, 480 x 272 pixels total, 16 colours, resistive touch screen. |
| Data Entry | Multiple entry methods; keyboard or touch screen selection of all major functions; edit field selection by screen touch or rotary control; value entry by keyboard, rotary control or touch screen; frequency and amplitude adjustable by value entry, character scrolling, user-defined step values or a combination. |
| Storage | 4G bytes internal storage available for 1000’s of instrument setups, sweep lists and user-defined modulation patterns. |
| Operating Range | +5°C to +40°C, 20 - 80% RH |
| Storage Range | –20°C to + 60°C |
| Environmental | Indoor use at altitudes up to 2000m, Pollution Degree 2. |
| EMC | Complies with EN61326 |
| Safety | Complies with EN61010-1 |
| Size | 2U high, half-rack width. |
| Weight | 3 kg |
| Options | 19-inch rack mounting kit. |
Be the first to review “TTi TGR2051 – 1.5GHz Synthesized RF Signal Generator”
Reviews
There are no reviews yet.